-
Mechanics
Balloon Puck Set
Apparatus may be used to explore the laws of motion without an air table and to study the inertia, constant velocity and acceleration and collisions in two dimensions. On flat smooth surface, the balloon puck can glide through without much resistance. Pucks ride on a film of air produced by air escaping from balloons, which are inflated and attached to the pucks. Kit includes two large pucks, two small pucks, four rubber stoppers, four tubes, four balloons and four rubber bands.
PH10516 -
Mechanics
Trajectory Apparatus
This unique low-cost trajectory apparatus allows the students to study the trajectory of a projectile. A steel ball launches from a ramp and collides with the target plate that is equipped with marking paper to record the point of contact manually. Move the target plate to different positions and the exercise is to plot the full trajectory of the ball. The kit consists of a wooden plotting board, two wooden supports, one steel ball, one cello tape roll, four graph papers and four marking papers. The apparatus is provided with full instructions.
PH10517A -
Mechanics
Collision in one Dimension
To demonstrate Newton’s third law of motion. Different number of balls is made to collide on a low-friction grooved track. Due to conservation of energy and momentum, we are able to predict a great deal about these collisions and to calculate relevant quantities after the collision occurs. With Five steel balls. 27″ track and instructions.
PH10518 -
Mechanics
Dynamic Cart Set
For experiments in velocity, acceleration, momentum, elastic collisions etc. The plastic carts have deep wells for additional masses, include two rubber bumpers for inelastic collisions, two spring loops for elastic collisions and an instructions. Each measures 13 x 5 x 3.5 cm and has a mass of 70 gm.
PH10523 -
Mechanics
Four Wheel Dynamic Cart
Dynamic carts with low friction ball bearing wheels and space to carry five ordinary brick. Each cart is supplied with one heavy and one light bumper spring, which can be easily changed. Complete with a loop spring and instructions. Each cart measures 7.5 x 25 cm, exclusive of wheels and bumper spring.
PH10525 -
Mechanics
Dynamic Carts
Sturdy steel body to withstand rough handling, with three low friction balls bearing wheels and aligned axles to ensure their rolling along a true line without deviation to provide accurate data. Each cart weighs about 1.5 kg. The cart bed is covered with a rubber pad and the ends of the cart rise above the bed to carry a brick or any other mass. A clip is provided at one end of the cart to attach a tape. The pins of each cart fit with holes on the other so that they can be stacked to double the mass.
PH10530 -
Mechanics
Fence and Picket Accessories for Dynamic Cart
Spare accessories for the dynamics cart include four picket fences works well with our Photo Gates PH10538G, each Fence comes with a 4 mm socket designed to fit into the cart.
Accessories Includes:
1. A Single picket fence
2. A Double picket fence
3. A Triple picket fence
4. A Ten-picket fence unitPH10531/ACC-02 -
Mechanics
Acceleration Trolley Apparatus
To demonstrate that gravitational acceleration down an incline is independent of the falling mass. The two-wheeled trolley runs across the room on an inclined overhead cable. Mounting hardware, 10.8 m of cable, and full operating instructions are supplied with the unit. Size is 15 x 10 cm. Mass set and hanger are not supplied with the apparatus.
PH10535 -
-
Mechanics
Ballistics Car
Demonstrate that the forward motion of a ball ejected vertically is the same as that of the vehicle from which it was ejected. A car with ball bearing wheels and vertically mounted spring-loaded barrel. The barrel permits two spring tensions. Complete with a 25 mm steel ball and release pin.
PH10537 -
Mechanics
Linear Air Track
Square section aluminium alloy track, length 1.5 m, with staggered holes, supported on two light alloy castings. One support has a two-point contact and other one-point contact for lateral and horizontal adjustments by means of a knurled screw. Identical end caps enable air to be introduced from either end of the track keeping the other end closed.
Linear Air Track Accessories Consisting of
2 Large vehicles (length 180 mm).
1 Small vehicle (length 140 mm).
2 Magnetic buffers (25 mm dia.).
2 Plasticine Holders (20 mm dia.) with central hole.
4 Catapults (45 mm wide) with slots for elastic band.
1 Reel of nylon thread.
2 White rods (4 mm dia. 150 mm long).
24 Needles.
20 Plain cards.
1 Reel rubber strand.
1 Pack of plasticine.
20 Elastic bands.
2 Needles with holder.
1 Instruction manual.Suggested Timer (NOT INCLUDED): PH10538TSuggested Photo Gates (NOT INCLUDED): PH10538GPH10538 -
Mechanics
Smart Photogate Timer
Photgate timer has been designed to measure the time interval between two photogates. It can measures the time it takes to pass through one photogate, measure acceleration of a released ball, determine the acceleration due to gravity (with a picket fence), determine elastic and inelastic collision times, calculate cycles, determine the period of a pendulum, count interrupts and time with stopwatch with great accuracy. All the results are displayed on a LCD Display. This timer allows you to watch the experiment as it happens and perform calculations easily and accurately. Includes a magnetic ball drop.
PH10538N
+1 (630) 345-3450